ServicesFurnace Repair
Furnace Repair in Garfield, WA
When your furnace quits, you want two things: heat back on and a straight answer about when we'll get there. We give you a realistic arrival window, call you if it shifts, and put a written quote in your hands before any repair starts.
Heat back on, without your day falling apart
We repair gas and electric forced-air furnaces from every major manufacturer. Most calls about no heat trace back to a short list of parts: a dirty flame sensor, a cracked hot surface igniter, a tired inducer motor or pressure switch, a weak blower capacitor, or a control board that stopped talking to the rest of the system. We find the one that failed, show you and fix it.
You likely shuffled your plans to be home for us, so we treat your time as part of the job. On the phone you get an arrival window we can actually keep. If a job before yours runs long, we call before your window is up, not after. Cold snaps here don't keep business hours, so we answer furnace calls 24/7 with no emergency or after-hours fees.
HVAC Garfield holds a Washington license and bond and carries $1M general liability insurance. That counts for something when a stranger is working on the burners and gas valve in your home.
What a furnace repair visit covers
Ignition and flame
We test and replace hot surface igniters, flame sensors, gas valves and the pilot assemblies on older units. A furnace that clicks, tries to light and gives up usually has a problem here.
Blower and airflow parts
Blower motors, run capacitors and belts on older furnaces get checked under load. We also look at your filter, because a clogged one can trip the high-limit switch and shut the burners off.
Controls and safety switches
Control boards, limit switches, pressure switches, rollout switches and thermostat wiring. We read the board's fault codes first so we're fixing the cause, not guessing.
A safety check before we leave
Every visit ends with a look at the heat exchanger, a check of the flue draft and a carbon monoxide reading near the furnace. If anything is unsafe, we tell you plainly and walk through your options.
Written quote and labor warranty
You see the price in writing before we replace a part. Our work comes with a 1-year labor warranty on all repairs.
When your furnace is telling you something is wrong
- Vents blowing cold
- The blower runs but the burners never catch, or they catch and go out within a minute. The usual suspects are ignition, the flame sensor or a pressure switch.
- Turning on and off every few minutes
- Constant starting and stopping wears parts out quickly and never gets the house fully warm. Overheating or a failing sensor is usually behind it.
- Sounds you haven't heard before
- A boom as it starts can be delayed ignition. A squeal often comes from a blower motor bearing or belt, and a rattle may be a loose panel or a bigger problem inside.
- Clicks but no fire
- The inducer motor runs and the igniter tries, then everything stops. It is often a small part, but it will not sort itself out.
- A CO alarm or a yellow flame
- When your CO alarm goes off, get everyone outside first and call 911 or your gas utility. After it's safe, call us and we'll track down the cause.
- Rising gas or electric bills
- Bills going up while the house feels no warmer usually means something inside is holding the system back, like a dirty burner, a weak blower or a part nearing the end of its life.
How your repair visit runs
- 1
You call, we set a real window
We ask what the furnace is doing and how long it's been happening. Then we give you an arrival window we expect to keep, not the most optimistic one.
- 2
A heads-up when plans change
Your tech calls when they're on the way. If an earlier job runs over, we call you right away with a new time so you're not stuck waiting at the door.
- 3
Diagnosis and a written quote
We test the system, read the fault codes and show you the failed part or photos of it. You get a written quote and an honest repair-or-replace answer. If replacing makes more sense on an older unit, we'll explain why and point you to our Furnace Installation page.
- 4
Fix it, prove it, tidy up
Once you approve the quote, we swap the part and watch the furnace go through several complete heat cycles. We take a second carbon monoxide reading, vacuum and wipe down where we worked, and explain the fix in everyday terms.
What sets the price of a furnace repair
The total mostly depends on which part quit and how easy it is to reach. The number is written down for you before any tool comes out. The diagnostic fee is credited toward the repair, so finding the problem doesn't cost you on top of fixing it.
- The part that gave out
- Cleaning a flame sensor or replacing an igniter is a quick job. A blower motor, inducer motor or control board calls for more parts and more hours.
- Brand and how easy parts are to get
- We carry many common parts on the truck. Certain brand-specific boards and gas valves must be ordered, which changes cost and timing, and we let you know which case yours is.
- How old and worn the furnace is
- When one part fails on an aging unit, others nearby may be wearing out too. We show you what we find and leave the decision to you instead of adding work ourselves.
- Where the unit is installed
- Working on a furnace in a cramped closet, attic or crawlspace takes more time than one sitting in an open basement.
- What time you reach us
- This one has no effect on your bill. With no emergency or after-hours fees, a repair at night costs the same as one during the day.
Furnace repair questions
- How soon can you get to me?
- It depends on the day and what's already on the schedule. When you call, we give you a realistic arrival window and stick to it, or call you early if something changes. We cover Garfield and nearby towns like Colfax, Pullman and Cheney.
- Is it worth repairing an older furnace?
- Often, yes. Many failures are single parts that bring an older furnace back for years. If the heat exchanger is cracked or repairs keep stacking up, we'll tell you honestly that replacement is the better spend and give you a free estimate on a new unit.
- What does your warranty cover?
- Every furnace repair we make comes with a 1-year labor warranty on all repairs. Keep your paperwork, and if something about our work isn't right during that year, give us a call.
- Can I try anything myself first?
- A few quick checks are worth a minute. Confirm the thermostat is on heat and its batteries aren't dead, flip the furnace breaker off and back on, and pull the filter to see if it's packed with dust. The door panel on the furnace also has to sit fully closed, because a safety switch keeps the unit off when it's loose. If you still have no heat after that, give us a ring and we'll take it from there.
- Will a Sunday night repair cost me extra?
- It won't. A furnace that dies at 2 a.m. or on a holiday is billed just like a Tuesday afternoon visit, since we don't add emergency or after-hours fees. The written quote still comes first, so you know the price before any part gets swapped.
- How do I avoid this happening again?
- Yearly tune-ups catch dirty sensors, weak capacitors and worn motors before they leave you cold. Our Maintenance Plans include tune-ups, repair discounts and priority scheduling.
Cold house? We'll come warm it up
Describe what the furnace is up to, and we'll set an arrival time you can plan your evening around. We pick up furnace calls at any hour, and nights cost the same as days.